OBJECTIVE: To evaluate the dose distribution in different situations of high dose-rate endobronchial brachytherapy, focusing especially on high-dose volumes, and try to identify better or worse situations in terms of dose distribution to aid as guidance in the clinical practice. MATERIALS AND METHODS: Theoretical study simulating high dose-rate endobronchial brachytherapy utilizing two catheters, varying the loading extent, angle between the catheters, prescription depth, and source step. With a prescription dose of 7.5 Gy, the volumes involved by the 100%, 150% and 200% isodoses (V100, V150 and V200, respectively) and V150/V100 and V200/V100 ratios were calculated. RESULTS: There was a volume enhancement with larger loaded lengths, increase in prescription depth and angles, with a tendency towards a proportionally smaller increase with larger angulations. In general, the V150/V100 and V200/V100 ratios were homogeneous, respectively around 0.50 and 0.30. CONCLUSION: Overall, the dose distribution in the standard situation was appropriate. No specific parameter that could be related to a higher toxicity was identified. The authors recommend a swift evaluation of the treatment quality through the analysis of the V150/V100 and V200/V100 ratios.

Keywords: Radiotherapy, Endobronchial brachytherapy, Dosimetry

OBJECTIVE: To calculate spectra of cobalt-60 beam at water depth and correction factors for absorbed dose measurements obtained with lithium fluoride thermoluminescent dosimeters using Monte Carlo simulation. MATERIALS AND METHODS: The simulations of secondary spectra of clinical cobalt-60 sources were performed with the PENELOPE Monte Carlo code at different water depths. Experimental measurements of deep doses were obtained with thermoluminescent dosimeters and ionization chamber under reference conditions for radiotherapy. Correction factors for the thermoluminescent dosimeters detectors were obtained through the ratio between the relative energy absorption for the low energy spectrum and the total spectrum. RESULTS: Deep spectral analysis has demonstrated the presence of secondary low-energy spectra responsible for a significant portion of the dose deposition. Discrepancies of 3.2% were observed among the doses measured with ionization chamber and thermoluminescent dosimeters. The adoption of correction factors has allowed a reduction in the discrepancy among absorbed doses to a maximum of 0.3%. CONCLUSION: Simulated spectra allow the calculation of correction factors for reading of thermoluminescent dosimeters utilized in the measurement of deep doses, contributing for the reduction of uncertainties associated with quality control of clinical beams in radiotherapy.

Keywords: Monte Carlo simulation, Radiotherapy, Spectrometry, Quality control, Thermoluminescent dosimetry, TLD

OBJECTIVE: The PENELOPE code was utilized to simulate irradiation geometries where heterogeneities are present and to simulate a photon beam behavior under these conditions. MATERIALS AND METHODS: For the homogeneous case, the ionizing radiation behavior was simulated only with water, and different materials were introduced to simulate heterogeneous conditions. Cubic geometries were utilized for the homogeneous phantoms, and parallelepiped-shaped geometries for the heterogeneities with the following composition: bone and lung tissue simulators, as recommended by the International Commission on Radiological Protection, and titanium, aluminum and silver. Input parameters were defined as follows: energy and type of source, 6 MV photons; source-surface distance=100 cm; and radiation field of 10x 10 cm². RESULTS: Percentage depth-dose curves were obtained for all the cases. As result, it was observed that for high electronic density materials, such as silver, the absorbed dose is higher than the absorbed dose in the homogeneous phantom, and for the lung tissue simulator, it is lower. CONCLUSION: Results clearly demonstrate the relevant role of heterogeneities in the treatment planning system algorithms utilized in the calculation of dose distribution in patients, increasing the accuracy of the dose delivered to the tumor and avoiding unnecessary irradiation of healthy tissues.

Keywords: Radiotherapy, Monte Carlo, PENELOPE, Heterogeneities, Depth-dose distribution

OBJECTIVE: Our purpose was to verify the effect of changes in subject contrast, exposure time and radiation dose when different thicknesses of molybdenum (Mo) and rhodium (Rh) filters are used in mammography equipments. MATERIALS AND METHODS: Entrance skin exposure measurements were performed with an ionization chamber for different thicknesses of Mo and Rh filters. Average glandular dose was determined with a BR12 simulator (50% fat tissue and 50% glandular tissue) of different thicknesses (4 cm and 8 cm). Energies in the range of 24 to 34 kVp and Kodak MinR 2000 films were used. RESULTS: Results have evidenced data on subject contrast data, glandular dose and exposure time for different thicknesses of additional filters and different kVp values. These data have indicated an increase both in values of subject contrast and exposure time when filters thickness is increased. The glandular dose has presented a different behavior tendency for each case analyzed. Equations were defined to allow us to estimate subject contrast, glandular dose and exposure time for the cases studied. CONCLUSION: The results have made possible to define equations to assist with the evaluation of subject contrast and glandular dose behavior in simulators with 4 cm and 8 cm thicknesses and for Rh and Mo additional filters. In this way, it is possible to estimate the figure of merit (subject contrast/glandular dose ratio) to assist in the risk-benefit analysis of the cases studied.

Keywords: Mammography, Radiation exposure, External dosimetry

OBJECTIVE: To present the solidly established traceability structure for ionometric standards and for thermoluminescent dosimetry system that ensures reliability of the Dosimetry Quality Assurance Program and is aimed to certify the highest level of accuracy of the measurements. MATERIALS AND METHODS: Thermoluminescent powder dosimeters (DTL 937) placed into plastic capsules and packed in specific kits for each intended application were mailed to the participant centers. RESULTS: The results of the intercomparisons performed between "Laboratório de Ciências Radiológicas da Universidade do Estado do Rio de Janeiro" and EQUAL-ESTRO for the beam of 60Co gamma rays, expressed for (1sigma), and the results of the dose absorbed measurements obtained with the chambers of the Program EQUAL and the chambers of the Dosimetry Quality Assurance Program were lower than 0.5%. CONCLUSION: Based on these results we concluded that the Dosimetry Quality Assurance Program reached the desired level of reliability to allow its implementation.

Keywords: Quality assurance, Radiotherapy, Dosimetric intercomparison, Thermoluminescent dosimetry, TLD

We compared chest radiographs using high and low kilovoltage techniques with the aim of obtaining best quality techniques as well as a reduction in patient doses. The study was performed in 48 patients randomized that were submitted to 70 postero-anterior chest radiographs using high (120 kVp, 2.3 mAs) and low (70 kVp, 5-10 mAs) kilovoltage techniques. The entrance skin dose values were measured with a Diamentor. The low kilovoltage technique showed a 326% increase of the dose when compared with the high kilovoltage technique. The use of the high kilovoltage technique decreased the number of low quality radiographs that required repetition, thus sparing the equipment and reducing the costs due to best quality radiographic images.

Keywords: Chest radiographs, Dosimetry, Image quality

Objective: To compare data regarding dosimetry and photons fluence in different breast phantoms, discussing constancy tests and dosimetry applied to mammography. Materials and methods: Different homogeneous breast phantoms and one anthropomorphic voxel phantom were developed for collection of data regarding total absorbed dose in the phantom, absorbed dose in the glandular tissue material-equivalent, absorbed dose and photons fluence at different depths in the phantoms. A simulated ionization chamber collected the entrance skin kerma. Target-filter combinations (Mo-30Mo and Mo-25Rh) were studied for different accelerating potentials of 26 kVp to 34 kVp. Results: As compared with the voxel phantom, the normalized glandular dose resulted in differences from –15% to –21% for RMI, –10% for PhantomMama, and 10% for the Barts and Keithley models. The half-value layer variation was generally < 10% for all the sensitive volumes. Conclusion: The phantom proposed by Dance is recommended for evaluating the glandular dose and normalized glandular dose in a standard breast. Homogeneous phantoms should be utilized for constancy tests in dosimetry, but they are not appropriate for estimating dosimetry in actual patients.

Keywords: Mammography; Dosimetry; Monte Carlo simulation; Geant4.

OBJECTIVE: The present study was aimed at characterizing a diamond detector and observing its behavior. MATERIALS AND METHODS: The dosimetric characteristics of 6 MV photon beams were measured by utilizing an automatic PTW MP3 scanning system with a diamond detector, and compared with measurements performed with a PTW 31010 ion chamber. RESULTS: Measurements of dose linearity, dose rate dependence and depth dose distribution as well as dose profiles demonstrated the dosimetric characteristics of the diamond detector. CONCLUSION: Some measurements with diamond detector and ion chamber were validated with results published in the literature, demonstrating a good behavior of the diamond detector as compared with the ionization chamber that is widely utilized for dosimetry in radiotherapy, indicating that the diamond detector is a good choice for small field dosimetry.

Keywords: Diamond; Dosimetry; Radiotherapy.

OBJECTIVE: To estimate extracranial doses on eyes, thyroid, chest and pelvis in patients submitted to radiosurgery with 6 MV linear accelerator. MATERIALS AND METHODS: The present study evaluated 11 patients, 7 of them with primary, and 4 with secondary brain tumors. In the latter group, 2 patients had two lesions. Thermoluminescent dosimeters were utilized to estimate the extracranial dose. Radiosurgery cones ranges between 1.50 and 3.75 cm and doses between 1300 and 2000 cGy. RESULTS: Mean patients' age was 52 years, and 63.6% of them were women and 36.4%, men. Lesion locations were the following: right acoustic nerve (1), frontal (2), parietal (5), right occipital (1), cerebellum (2) and parasagittal (2). Mean received doses were the following: 5.1 cGy between the eyes; 4.8 cGy in the right eye; 6.5 cGy in the left eye; 4.2 cGy in the thyroid; 1.65 cGy in the chest; and 0.45 cGy in the pelvis. CONCLUSION: The results demonstrate that that although the eye doses do not exceed the tolerance limits for occurrence of lens opacity, it is important that the risks associated with radiation doses are taken into consideration by radiotherapists in the planning of cranial radiosurgery procedures.

Keywords: Brain tumor; Radiotherapy; Radiosurgery; Dosimetry.

OBJECTIVE: The present study was aimed at estimating the doses received by physicians and patients during cerebral angiography procedures in a public hospital of Recife, PE, Brazil. MATERIALS AND METHODS: The study sample included 158 adult patients, and during the procedures the following parameters were evaluated: exposure parameters (kV, mAs), number of acquired images, reference air kerma value (K_a,r) and air kerma-area product (P_KA). Additionally, the physicians involved in the procedures were evaluated as for absorbed dose in the eyes, thyroid, chest, hands and feet. RESULTS: The results demonstrated that the doses to the patients' eyes region were relatively close to the threshold for cataract occurrence. As regards the physicians, the average effective dose was 2.6 µSv, and the highest effective dose recorded was 16 µSv. CONCLUSION: Depending on the number of procedures, the doses received by the physicians may exceed the annual dose limit for the crystalline lenses (20 mSv) established by national and international standards. It is important to note that the high doses received by the physicians are due to the lack of radiation protection equipment and accessories, such as leaded curtains, screens and protective goggles.

Keywords: Dosimetry; Interventional radiology; Cerebral angiography.

OBJECTIVE: Aiming at contributing to the knowledge on doses in computed tomography (CT), this study has the objective of determining dosimetric quantities associated with pediatric abdominal CT scans, comparing the data with diagnostic reference levels (DRL). MATERIALS AND METHODS: The study was developed with a Toshiba Asteion single-slice CT scanner and a GE BrightSpeed multi-slice CT unit in two hospitals. Measurements were performed with a pencil-type ionization chamber and a 16 cm-diameter polymethylmethacrylate trunk phantom. RESULTS: No significant difference was observed in the values for weighted air kerma index (C_W), but the differences were relevant in values for volumetric air kerma index (C_VOL), air kerma-length product (P_KL,CT) and effective dose. CONCLUSION: Only the C_W values were lower than the DRL, suggesting that dose optimization might not be necessary. However, P_KL,CT and effective dose values stressed that there still is room for reducing pediatric radiation doses. The present study emphasizes the importance of determining all dosimetric quantities associated with CT scans.

Keywords: Pediatric computed tomography scans; Dosimetric quantities; Weighted dose index; Volumetric air kerma index; Air kermalength product.

OBJECTIVE: This article presents a way to obtain estimates of dose in patients submitted to radiotherapy with basis on the analysis of regions of interest on nuclear medicine images. MATERIALS AND METHODS: A software called DoRadIo (Dosimetria das Radiações Ionizantes [Ionizing Radiation Dosimetry]) was developed to receive information about source organs and target organs, generating graphical and numerical results. The nuclear medicine images utilized in the present study were obtained from catalogs provided by medical physicists. The simulations were performed with computational exposure models consisting of voxel phantoms coupled with the Monte Carlo EGSnrc code. The software was developed with the Microsoft Visual Studio 2010 Service Pack and the project template Windows Presentation Foundation for C# programming language. RESULTS: With the mentioned tools, the authors obtained the file for optimization of Monte Carlo simulations using the EGSnrc; organization and compaction of dosimetry results with all radioactive sources; selection of regions of interest; evaluation of grayscale intensity in regions of interest; the file of weighted sources; and, finally, all the charts and numerical results. CONCLUSION: The user interface may be adapted for use in clinical nuclear medicine as a computer-aided tool to estimate the administered activity.

Keywords: Nuclear medicine; Biokinetic distribution; Dosimetric evaluations; Administered activity.

OBJECTIVE: To evaluate the level of ambient radiation in a PET/CT center. MATERIALS AND METHODS: Previously selected and calibrated TLD-100H thermoluminescent dosimeters were utilized to measure room radiation levels. During 32 days, the detectors were placed in several strategically selected points inside the PET/CT center and in adjacent buildings. After the exposure period the dosimeters were collected and processed to determine the radiation level. RESULTS: In none of the points selected for measurements the values exceeded the radiation dose threshold for controlled area (5 mSv/year) or free area (0.5 mSv/year) as recommended by the Brazilian regulations. CONCLUSION: In the present study the authors demonstrated that the whole shielding system is appropriate and, consequently, the workers are exposed to doses below the threshold established by Brazilian standards, provided the radiation protection standards are followed.

Keywords: Dosimetry; Thermoluminescence dosimetry; PET/CT.

OBJECTIVE: Derive filtered tungsten X-ray spectra used in digital mammography systems by means of Monte Carlo simulations. MATERIALS AND METHODS: Filtered spectra for rhodium filter were obtained for tube potentials between 26 and 32 kV. The half-value layer (HVL) of simulated filtered spectra were compared with those obtained experimentally with a solid state detector Unfors model 8202031-H Xi R/F & MAM Detector Platinum and 8201023-C Xi Base unit Platinum Plus w mAs in a Hologic Selenia Dimensions system using a direct radiography mode. RESULTS: Calculated HVL values showed good agreement as compared with those obtained experimentally. The greatest relative difference between the Monte Carlo calculated HVL values and experimental HVL values was 4%. CONCLUSION: The results show that the filtered tungsten anode X-ray spectra and the EGSnrc Monte Carlo code can be used for mean glandular dose determination in mammography.

Keywords: Mammography; X-ray spectra; HVL; Monte Carlo.

OBJECTIVE: To perform a comparative dosimetric analysis, based on computer simulations, of temporary balloon implants with ^99mTc and balloon brachytherapy with high-dose-rate (HDR) ¹⁹²Ir, as boosts to radiotherapy. We hypothesized that the two techniques would produce equivalent doses under pre-established conditions of activity and exposure time. MATERIALS AND METHODS: Simulations of implants with ^99mTc-filled and HDR ¹⁹²Ir-filled balloons were performed with the Siscodes/MCNP5, modeling in voxels a magnetic resonance imaging set related to a young female. Spatial dose rate distributions were determined. In the dosimetric analysis of the protocols, the exposure time and the level of activity required were specified. RESULTS: The ^99mTc balloon presented a weighted dose rate in the tumor bed of 0.428 cGy.h^-1.mCi^-1 and 0.190 cGyh^-1.mCi^-1 at the balloon surface and at 8-10 mm from the surface, respectively, compared with 0.499 and 0.150 cGyh^-1.mCi^-1, respectively, for the HDR ¹⁹²Ir balloon. An exposure time of 24 hours was required for the ^99mTc balloon to produce a boost of 10.14 Gy with 1.0 Ci, whereas only 24 minutes with 10.0 Ci segments were required for the HDR ¹⁹²Ir balloon to produce a boost of 5.14 Gy at the same reference point, or 10.28 Gy in two 24-minutes fractions. CONCLUSION: Temporary ^99mTc balloon implantation is an attractive option for adjuvant radiotherapy in breast cancer, because of its availability, economic viability, and similar dosimetry in comparison with the use of HDR ¹⁹²Ir balloon implantation, which is the current standard in clinical practice.

Keywords: Breast brachytherapy; Balloon; Radiotherapy dosage; Radiotherapy, adjuvant; ^99mTc; ¹⁹²Ir; Monte Carlo method.